Drop Deck Feed Trailer

The Ledwell Drop Deck Feed Trailer is perfect for those needing to haul a substantial amount of feed, wood pellets, or other material. There is a slight drop in the frame located at the front of the trailer creating a lower center of gravity.

Our Drop Deck Bulk Feed Trailer is available with a choice between a Drag Chain or Auger bottom, both offer consistency and quick delivery. The Drop Deck Feed Trailer comes equipped with our signature Ledwell Torque Converter System designed to prevent overheating and reduce maintenance needs.

SKU: Drop Deck Trailer Category: Tags: , , , , ,

Description

If you’re in need of a reliable trailer to transport large quantities of feed, wood pellets, or other materials, the Ledwell Drop Deck Feed Trailer is the solution you’ve been looking for. Its front frame features a slight drop, providing a lower center of gravity that enhances stability during transportation.

Choose between a Drag Chain or Auger bottom to ensure consistent and speedy delivery with our Drop Deck Bulk Haul Trailer. Our signature Ledwell Torque Converter System also prevents overheating and reduces maintenance needs, so you can haul with peace of mind.

Experience the convenience and reliability of the Ledwell Drop Deck Feed Trailer for all your hauling needs. Contact us today to get yours!

SPECS

Low center of gravity
Extruded keel
Various compartments configurations
25 to 40 ton hauling capacity

FEATURES

Air-operated side slide or manual roll tarp top doors
Air-operated or manual rack & pinion bottom doors
Auger  or Drag Chain floor delivery
Full-function wireless remote
Rear hydraulic controls

SAFETY

DOT-approved lights and reflectors
Fire extinguisher
Backup alarm
Emergency reflectors
Conspicuity tape

OPTIONS

SMART system
Vacuum reclaimer
Air discharge blower
Sack Boxes
Self-contained engine
Curbside catwalk & rear ladder
Air operated handrail

Bulk Haul Trailer Resources

LITERATURE

VIDEOS

FEED TRAILER FAQS

Auger Bulk Feed Equipment

How do I operate an Auger feedbody or feed trailer?

Operating your Ledwell Bulk Feed Equipment correctly is vital to extend the life of your Auger feed equipment. Watch this operational series video or follow the steps below.

To get started, walk around the entire trailer to inspect the following:
Overhead and ground obstructions, Hydraulic Valves in the neutral position, Hydraulic and Air Hoses, Lights, Wheels and Tires, Remote control.

TO LOAD:
Pull up to the mill and position as needed.
Check that your bottom doors are closed.
Open the top doors Fill the bins of the trailer.

TO UNLOAD:
Engage the PTO Push raise and out on the remote to move the discharge boom away from the trailer.
Use the remote control to position the discharge over the silo.
Push discharge on Push floor on Open the bin closest to the rear – remembering to unload from back to front.
Leave each door open as you move forward.
Check the discharge gauge – it should be around 1400 PSI for 9x9x9 or 1900 – 2000 for 12x12x12.
Check the floor gauge – the PSI should be around 1000 to 1500 for an Auger system – the PSI will depend on which bay you are pulling from.
Adjust flow control on the floor to achieve 1400 PSI on the discharge gauge – the PSI will vary depending on feed type.
As the bin empties, the pressure will drop on gauges – this is how you will know to open the next bin.
Once all bins are empty, Push the floor off.
Push discharge off.
Push lower and in to place the discharge boom back in the saddle.
Make sure to close all bottom doors.

Do you offer a biosecurity system for feed equipment?

Yes, our Bio Security Kit is available on new feed trucks or trailers and as a retrofittable kit for existing bulk feed equipment.

What is the optimal pressure for the discharge on an Auger Bulk Haul?

Pressure for the discharge should be around 1400 PSI for a 9x9x9 or 1900 – 2000 for a 12x12x12 discharge system.

What is the optimal pressure for the floor on an Auger Trailer?

Pressure for the floor should be around 1000 to 1500 for an Auger system – the PSI will depend on which bay you are pulling from.

Drag Chain Feed Equipment

How do I operate a chain bottom feed trailer?

Operating your Ledwell Bulk Feed Equipment correctly is vital to extend the life of your Drag Chain Trailer. Watch this operational series video or follow the steps below.

To get started, walk around the entire trailer to inspect the following:
Overhead and ground obstructions, Hydraulic Valves in the neutral position, Hydraulic and Air Hoses, Lights, Wheels and Tires, Remote control.

TO LOAD:
Pull up to the mill and position as needed.
Check that your bottom doors are closed.
Open the top doors Fill the bins of the trailer.

TO UNLOAD:
Engage the PTO Push raise and out on the remote to move discharge boom away from the trailer.
Use the remote control to position the discharge over the silo.
Push discharge on Push floor on Open the bin closest to the rear – remembering to unload from back to front.
Leave each door open as you move forward.
Check the discharge gauge – it should be around 1400 PSI for 9x9x9 or 1900 – 2000 for 12x12x12.
Check the floor gauge – the PSI should be around 600 PSI for a Drag Chain from any bay.
Adjust flow control on the floor to achieve 1400 PSI on the discharge gauge – the PSI will vary depending on feed type.
As the bin empties, the pressure will drop on gauges – this is how you will know to open the next bin.
Once all bins are empty, Push the floor off.
Push discharge off.
Push lower and in to place the discharge boom back in the saddle.
Make sure to close all bottom doors.

Do you offer a biosecurity system for bulk feed equipment?

Yes, our Bio Security Kit is available on new feed trucks or trailers and as a retrofittable kit for existing bulk feed equipment.

What is the optimal pressure for the discharge on a Drag Chain Bulk Haul?

Pressure for the discharge should be around 1400 PSI for a 9x9x9 or 1900 – 2000 for a 12x12x12 discharge system.

What is the optimal pressure for the floor on a Drag Chain?

Pressure for the floor should be around 600 PSI for Drag Chain Feed Equipment from any bay.

Severe Duty Cooler

What is the max PSI for my Hydraulic Cooler?

The Ledwell Severe Duty Cooler is rated for return line pressure up to 300 PSI maximum.

Are Severe Duty Cooler parts available to order?

Yes, there are several parts available to upgrade or replace on your Hydraulic Cooler. Contact our Parts Department for a quote.

What is the maximum flow rate that a Severe Duty Cooler can support?

The SDC is routinely used in systems up to 70 gpm.

YOU MIGHT ALSO NEED