Description
The Ledwell Classic Bulk Haul Trailer is the ultimate solution for your bulk delivery needs. Our trailers are customer-centric and designed to meet your specific requirements. With two delivery options, you can select either the Drag Chain Bottom or Auger system, depending on your preference.
Ledwell understands the importance of reliability and efficiency, which is why both delivery systems come equipped with our unique Ledwell Torque Converter System. This innovative system prevents trailer overheating and reduces maintenance requirements, providing peace of mind and savings in the long run. Choose the Ledwell Classic Bulk Haul Trailer delivery system for superior performance and hassle-free operation.
SPECS
28′ to 45′ body lengths
Extruded keel
Various compartments configurations
25 to 40 ton hauling capacity
FEATURES
Air-operated side slide or manual roll tarp top doors
Air-operated or manual rack & pinion bottom doors
Auger or Drag Chain floor delivery
Full-function wireless remote
Rear hydraulic controls
SAFETY
DOT-approved lights and reflectors
Fire extinguisher
Backup alarm
Emergency reflectors
Conspicuity tape
OPTIONS
SMART system
Vacuum reclaimer
Air discharge blower
Sack Boxes
Self-contained engine
Curbside catwalk & rear ladder
Air operated handrail
Ledwell’s bulk feed trailers are built to endure years of hard work on your fleet.
“Ledwell is the best when it comes to pellet quality,” Dusten said. “If anybody out there is ever having problems with fines in pellets or unloading a heavy mineral, they need a Ledwell.”
Munson Lakes purchased new bulk haul bodies as well as used Ledwell trailers, which Ledwell completely refurbishes before reselling. Munson Lakes bought their first Ledwell in 1987. The oldest Ledwell equipment they have on the lot right now is a ’94, and the oldest they use daily is a 2004.
“You can’t buy another piece of equipment and maintain it for as little cost as a Ledwell,” Dusten said. “They don’t break down. The cost to repair them when they do is minimal. They always answer the phone when I need parts.”
FEED TRAILER FAQS
Auger Bulk Feed Equipment
How do I operate an Auger feedbody or feed trailer?
Operating your Ledwell Bulk Feed Equipment correctly is vital to extend the life of your Auger feed equipment. Watch this operational series video or follow the steps below.
To get started, walk around the entire trailer to inspect the following:
Overhead and ground obstructions, Hydraulic Valves in the neutral position, Hydraulic and Air Hoses, Lights, Wheels and Tires, Remote control.
TO LOAD:
Pull up to the mill and position as needed.
Check that your bottom doors are closed.
Open the top doors Fill the bins of the trailer.
TO UNLOAD:
Engage the PTO Push raise and out on the remote to move the discharge boom away from the trailer.
Use the remote control to position the discharge over the silo.
Push discharge on Push floor on Open the bin closest to the rear – remembering to unload from back to front.
Leave each door open as you move forward.
Check the discharge gauge – it should be around 1400 PSI for 9x9x9 or 1900 – 2000 for 12x12x12.
Check the floor gauge – the PSI should be around 1000 to 1500 for an Auger system – the PSI will depend on which bay you are pulling from.
Adjust flow control on the floor to achieve 1400 PSI on the discharge gauge – the PSI will vary depending on feed type.
As the bin empties, the pressure will drop on gauges – this is how you will know to open the next bin.
Once all bins are empty, Push the floor off.
Push discharge off.
Push lower and in to place the discharge boom back in the saddle.
Make sure to close all bottom doors.
Do you offer a biosecurity system for feed equipment?
Yes, our Bio Security Kit is available on new feed trucks or trailers and as a retrofittable kit for existing bulk feed equipment.
What is the optimal pressure for the discharge on an Auger Bulk Haul?
Pressure for the discharge should be around 1400 PSI for a 9x9x9 or 1900 – 2000 for a 12x12x12 discharge system.
What is the optimal pressure for the floor on an Auger Trailer?
Pressure for the floor should be around 1000 to 1500 for an Auger system – the PSI will depend on which bay you are pulling from.
Drag Chain Feed Equipment
How do I operate a chain bottom feed trailer?
Operating your Ledwell Bulk Feed Equipment correctly is vital to extend the life of your Drag Chain Trailer. Watch this operational series video or follow the steps below.
To get started, walk around the entire trailer to inspect the following:
Overhead and ground obstructions, Hydraulic Valves in the neutral position, Hydraulic and Air Hoses, Lights, Wheels and Tires, Remote control.
TO LOAD:
Pull up to the mill and position as needed.
Check that your bottom doors are closed.
Open the top doors Fill the bins of the trailer.
TO UNLOAD:
Engage the PTO Push raise and out on the remote to move discharge boom away from the trailer.
Use the remote control to position the discharge over the silo.
Push discharge on Push floor on Open the bin closest to the rear – remembering to unload from back to front.
Leave each door open as you move forward.
Check the discharge gauge – it should be around 1400 PSI for 9x9x9 or 1900 – 2000 for 12x12x12.
Check the floor gauge – the PSI should be around 600 PSI for a Drag Chain from any bay.
Adjust flow control on the floor to achieve 1400 PSI on the discharge gauge – the PSI will vary depending on feed type.
As the bin empties, the pressure will drop on gauges – this is how you will know to open the next bin.
Once all bins are empty, Push the floor off.
Push discharge off.
Push lower and in to place the discharge boom back in the saddle.
Make sure to close all bottom doors.
Do you offer a biosecurity system for bulk feed equipment?
Yes, our Bio Security Kit is available on new feed trucks or trailers and as a retrofittable kit for existing bulk feed equipment.
What is the optimal pressure for the discharge on a Drag Chain Bulk Haul?
Pressure for the discharge should be around 1400 PSI for a 9x9x9 or 1900 – 2000 for a 12x12x12 discharge system.
What is the optimal pressure for the floor on a Drag Chain?
Pressure for the floor should be around 600 PSI for Drag Chain Feed Equipment from any bay.
Severe Duty Cooler
What is the max PSI for my Hydraulic Cooler?
The Ledwell Severe Duty Cooler is rated for return line pressure up to 300 PSI maximum.
Are Severe Duty Cooler parts available to order?
Yes, there are several parts available to upgrade or replace on your Hydraulic Cooler. Contact our Parts Department for a quote.
What is the maximum flow rate that a Severe Duty Cooler can support?
The SDC is routinely used in systems up to 70 gpm.
